SUVCargoliners

Truck Bed Liner

Home | Truck Bed Liner | slip on car cover | floor mat | Seat Covers | portable air compressor | electric extension cord | garage battery charger | hand trucks-dollies | load strap | load tarp

BannerFans.com

cargoliners

Complete Roll-On Truck Bed Liner Kit With Herculiner, it's easy to roll on a truck bed liner that won't chip, flake or peel. Herculiner's textured rubber and polyurethane formula will turn any truck bed into a tough, skid-proof, rust-resistant surface. With Herculiner, "The Tough Comes Easy." You can save hundreds of dollars compared to dealer-installed spray-on bed liners. Clean, scuff, and mask your truck bed and you're ready to apply Herculiner. Brush or roll on the ready-to-use coating and it's dry to touch in 1-3 hours, ready to use in 9-12 hours. However, with over 101 uses, Herculiner is not just a bed liner. This unique, advanced formula protective coating can be used for automotive undercoating, trailers, steps, boat decks, docks and ramps, vinyl tile floors and work areas, and much more. Includes enough liner for one 6' bed. Features: Textured, Polyurethane & Rubber Formula Skid Resistant Won't Chip, Flake, or Peel Apply to Metal, Concrete, Wood, Fiberglass, Most Plastics (Including PVC), and Rubber Ready to use, Easy to Apply Fast Drying Attractive Black Textured Finish Prevents Rust and Corrosion Waterproof, Resistant to Chemicals and Acids Repairable - Bonds to Itself Spray Applicable (Instructions Inside Box). Kit Includes: One Gallon of Ready-to-Use Protective Coating One Applicatioin Brush for Tight Spots and Corners Two Rollers for Easy, Even Application One Roller Handle One Abrasive Pad to Prepare Truck Bed

Below is a text description of what you might find here from time to time-this is only an example.



This sale is for 4 plastic quart bottles of White Bed Liner (SMR-1000W) and a quart of SMR-222 activator; which when mixed yields one gallon sprayable. Also included is a mixing cup for measuring activator and a free shutz spray gun to apply the bed liner.

Coverage is 15-30 Square Feet per Quart of T-Rex Bed-Liner.

Note: If one gallon of sprayable bedliner is not enough for your job, then you may add SMR-1000W-K1 from ebay.

The SMR-1000W is a 1.7 lbs/gallon voc and is the only bed liner that is 50 state compliant.


SMR-1000W is a true 2K urethane with outstanding adhesion to steel and sanded paint.

This coating is formulated to withstand the same atmospheric conditions as a high quality single stage urethane topcoat.


FEATURES:

.True 2K Urethane Durability

.Uniform White Color
.Excellent Exterior Stability from UV Light

.Fast Dry

.Chemical Resistant Finish
• Easy to use: ADD hardener - SHAKE - SPRAY (see instructions below)
• Abrasion and Stain Resistant
• Protects against rust, corrosion salt, damp & extreme temperatures
• Waterproof, flexible, helps deaden sound & vibrations
• Apply with shutz gun at different pressures to obtain different textures
• Provides excellent adhesion



SURFACE PREPARATION:


Surface should be cleaned of all grease, oil, dirt, rust, etc before sanding.

Wash area with soap and warm water, then rinse and dry.

Thoroughly clean area with Wax and Grease Remover.

Scuff surface with 180-220 grit sandpaper.

Re-clean with wax and grease remover, then dry with a clean towel.




Instructions: Apply Bed Liner between 60 - 85 degrees F and humidity less than 70%, Not in direct sunlight.



1. Add 8 ounces of SMR-222 activator to a quart bottle of SMR-1000W.

2. Screw on quart bottle cap and shake for two minutes.

3. Remove the cap and screw in the Shutz Spray Gun.

4. Adjusting the air pressure (60-80 PSI) and spray distance will change the texture.

5. Apply a uniform wet coat of bed liner using a sweeping motion.

6. After a 2 minute flash, apply a very light 2nd coat, sprayed at 80 PSI, using a fast sweeping motion.



Specification:
Usable Pot life at 70 degrees F / 20 degrees C : 60 minutes
Touch Dry at 70 degrees F / 20 degrees C : 1 hour subject to film build.
Light duty: 2 days at 70 degrees F / 20 degrees C.
Regular duty: 5 days at 70 degrees F / 20 degrees C.